|
|
Penals and Profile Production
Line
1)PC,PP,PE, and PVC
Plastic Hollow Cross Section Plate Extrusion Line
Application:
 Construction
of sunroof in buildings, halls, shopping centers, stadiums,
public places of entertainment and public facilities
Rain shed of bus stations, garages, pergolas, corridors.
Transparent shields for security forces in nursery school,
airports, and factories.
Skylight of modern agriculture and aquacultures, indoor
pools sign board for ads, light box and exhibition service
Ceilings partition walls and exhibition stands partition
in office and residence.
2)PVC Wide Plate Extrusion Line
Roperties and Advantages:
Series PVC wide plate extrusion line has compact structure,
good plasticization, high output, long life and other
advantages. This line uses SJZ80 conical twin screw extruder
with alternating-current inverter, imported electronic
components and PT 100 platinum resistance, which provide
wide adjusting range and precise temperature control.
The down stream equipment includes vacuum calibration
and cooling unit, haul-off unit, cutting machine and stacker.
 The
calibration unit is equipped with large forced cooling
system so that it can provide perfect calibration effect.
The haul-off unit uses two line caterpillars. The lower
line is fixer and the upper one can be adjusted according
to the plate size.
The cutting machine is equipped with PLC control system
which helps to set length and provide accurate automatic
cutting.
The stacker is covered with rubber grip blocks to prevent
products from damage.
3)PET Baling Strap Production Line
PET Baling Strap Production Line Introduction:
The PET baling strap production line is a newly developed
production line is a newly developed production line by
our company.
During the research period, we have made long time production
practices and learnt form both domestic and abroad machines.
This equipment adopts the frequency conversion motor as
the power source. The mechanical transmission has the
features of the precise and stable transmission, save
energy and low noise with the soft connection is applied.
Our PET bailing strap production line could use the crushed
PET bottles (such as cola bottles) as raw material, thus
the cost of raw material could be sharply reduced and
the profit could be 50% higher compared to use virgin
PET.
Characters:
PET has the features of good rigidity, high temperature
resistance and rustless. Its specific gravity is 1/5 of
steel. The PET baling strap is mainly used in the packing
field of factories. The PET strap has the following characters:
high tensile strength, small ductility, anti bounce, low
cost, excellent flexibility, easy operation and high reliability.
The PET baling strap is an ideal product to replace steel
strap. It could be used for baling paper, wood, textile,
cotton and fiber, metal, can ,chemical, cable and plastic
profiles, etc. This strap is east to use and could be
connected by normal steel fastener. It could also be connected
by thermal melting.
4)PVC Profiles Extrusion Line
Features and application:
PVC profile production line suitable to produce
PVC profile, multi-hole cable duct (4-hole, 6-hole, 7-hole,
9-hole option). According to different profile section
and mold to choose different conical or parallel twin
screw extruder and provide relative vacuum sizing tank,
hail-off , cross direction saw cutter, stacker auxiliary
equipments. The capacity of main extruder is from 150kg
/hour to 450kg /hour for option. Special design for haul-off
by particular up and down technology of our company, working
stable, reliable and heavy duty force. Vacuum sizing tank
having particular big eddy flow cooling system for cooling
and sizing easy for high speed extruding necessary. The
action of cross direction saw cutter keeping synchronous
with haul-off controlled by import PLC controller, reasonable
design, running stable, auto fixed length cutting, assembled
swarf suction device. According to different mold, the
vacuum sizing tank could be provided of 4 meter, 6meter,
8meter, 11meter models. Providing parallel twin screw
extruder for high speed extruding.
Pipes Production Line
1)PE Double Wall Corrugated Pipe Main features.
• It adopts efficient screw and notched barrel,
the inner and outer walls are separately extruded by two
extruders for using different materials and ensuring efficient
extruding.
• A high speed of production can be ensured
by the corrugated forming system and forced cooling system
combined with water and air cooling during constant production.
The advanced programmable lubricating system decreases
abrasion of mould blocks to a minimum while lengthening
their lifespan and ensuring running precision and stable
quality.
• The advanced inline double wall belling function
can reach or exceed the requirement of the state standard,
completely solving disadvantages of the pipe creep and
leakage of sealing in sockets.
• Co-extrusion die with special structure makes
the inner and outer walls even and step less adjustable,
and forming stable.
• The cast mould blocks are made from special
alloy for high precision and strength and excellent radiation
effect.
• A professional PCC (B&R, Austria ) control
system is adopted with 15” touched colour screen for high
automation, reliable running and easy operation.
• It adopts a quick changing system for the
mould blocks
• The optimum design of crest provides a perfect
combination of higher ring stiffness and lower unit weight.
• Long-distance communicative function can
realize tele-diagnosis and maintenance.
• The key and new product of the State
• It is certified for CE quality system by
China Quality Certification Centre.
2)PVC Double Wall Corrugated Pipe
3)PE Solid Pipe
4)PVC Solid Pipe
5)Steel Plastic Sprial Pipe
6)Al-plastic Composite Pipe
7)PEX Pipe
8)PPR Pipe
|
PVC Double Wall Corrugated Pipe
|
Technical Data
| Model
|
SBG-250 |
SBG-500 |
SBG-1000 |
SBG-1500 |
| Pipe
diameter range (ID),mm |
Φ 100- Φ 250 |
Φ 200- Φ 400 |
Φ 200- Φ 800 |
Φ 800- Φ 1200 |
| Extruder
structure |
SJPE-65/25B |
SJPE-65/30B |
SJPE-90/30B |
SJPE-120/30B |
|
|
SJPE-90/30B |
SJPE-65/25B |
SJPE-120/30B |
SJPE-150/30B |
| Extrusion
die, mould |
Φ 100, Φ 125, Φ 150,
Φ 200, Φ 225, Φ 250 |
Φ 200, Φ 225, Φ 250,
Φ 300, Φ 400 |
Φ 200, Φ 225, Φ 250,
Φ 300, Φ 400, Φ 500, Φ 600, Φ 800 |
Φ 800, Φ 1000, Φ 1200
|
| Corrugated
|
SBGC-250 |
SBGC-500 |
SBGC-1000 |
SBGC-1500 |
| Forming
machine |
Vertical style |
Vertical style |
Vertical style |
Vertical style |
| Spray
cooling flume |
SGL-250 |
SGL-500 |
SGL-1000 |
SGL-1500 |
| Cutting
machine |
SGL-250 |
SGL-500 |
SGL-1000 |
SGL-1500 |
| Stacker
|
SGL-500 |
SGL-500 |
SGL-1000 |
SGL-1500 |
| Productivity,
kg/h |
500 |
600 |
900 |
1200 |
| Installed
power, KW |
350 |
450 |
730 |
950 |
| Dimension(L*W*H),m
|
3 0 × 4.5 × 3.1 |
3 0 × 4.5 × 3.1 |
3 4 × 4.8 × 5.32 |
4 0 × 7.4 × 4.9 |
| Total
weight, t |
28 |
48 |
76 |
105 |
PU Foaming Equipments
The machine is developed to meet the increasing
demand of CFCS replacement work. It apples CO 2 as foaming
material. It's the latest foaming technology in the world.
Therefore it has broad developing prospects.
1) PU Low pressure Foaming Machine
The PU low pressure foaming machine's functional sequence:
the low pressure components are pumped to the mixing head
by means of high precision metering pump and stirred with
a high speed by an agitator within the mixing chamber
and pouring out the mixture with highly constant weight.
It can be used widely in RIM for various PU products.
Mixing ratio: 1:5—5:1
 Metering
precision: <1%
Injecting precision: <5‰ components temperature
Control: ± 1°C
2) Refrigerator Foaming Line
3) Automobile Interior Decoration Parts Foaming Line
This ZT turnaround production line which is suitable to
produce various kind of vehicle inner decorating material
of Polyurethane is a system of multi application, especially
is suitable for litter varieties and a large scale. Diameter
of revolving table is 4000 -11000mm . One the revolving
table dies and die supports of multi—size can be installed,
die may open and close automatically. Rotating speed can
be adjusted and accuracy of fixing station is high.
4) PU Sandwich Panel Line
The use of PU sandwich panel is with widely range. It
could be used for cold  storage,
refrigerator car, showing board, etc. In order to produce
the PU sandwich panel, we developed serious types of laminating
press, Inc. Single plate laminating press and multi-plate
laminating press, etc.
The photo above shows 5-plate laminating press. It could
inject 5 panels in the meantime. It applies hydraulic
drive. The Max. clamping force can reach 130tons and its
lifting weight can reach 5tons.
Plastic Wood Products & PVC Profiles
1) PVC Profiles Extrusion Line
2) Plastic Wood Machinery
BLOWN FILM Series Equipments
1) THREE-LAYER COEXTRUSION HEAVY DUTY BLOWN FILM LINE
2) MULTI-LAYER COEXTRUSION BLOWN
FILM LINES
 The line is
combined with many international high and new patented
technologies such as: 1. Latest double mixing screw; 2.
Forced feeding barrel; 3. Central material supplying system;
4. Automatic film profile detecting system; 5. Automatic
film profile thickness adjusting control system (automatic
air ring); 6. Continuous gravimetric measurement and control
system for preciously controlling the thickness proportion
of each layer; 7. Seven-layer co extruded planed stackable
streamline die head; 8. IBC (Internal bubble cooling)
system; 9. Horizontal reversing haul-off system; 10. Film
thickness probe; 11. Dual-photoelectric automatic central
web guiding system; 12. Fully automatic dual-slitter and
dual- Winding gap winder with tension control; 13. Computer
integrated control, etc. The line is made to produce symmetry
or unsymmetry barrier film with high barrier performance,
high mechanical strength and good transparency property.
The barrier of the film can be up to three layers. It
is an ideal high barrier and high performance package
material for food, agricultural and sideline products,
medical treatment (taking orally and injection medicament,
blood, medical apparatus), pesticide, chemical industrial
products, daily articles and war industry articles.
3) M3B-A SERIES THREE-LAYER COEXTRUSION
BLOWN FILM LINES (HIGH-OUTPUTTYPE)
M3B-A SERIES THREE-LAYER COEXTRUSION BLOWN FILM LINES
(HIGH-OUTPUT TYPE) are high-quality and high-output products
in our company, and cater to the characters of Chinese
Market, which adopt the advanced technology and equipments,
such as extruder with force feeding function, precision
ceramic heater, precision dual lip air ring, horizontal
reversing haul-off system, IBC internal bubble cooling
system, the first haul-off system with cooling function,
fully automatically two-slitter and two-winding surface
winder, computer integrated control system etc. The lines
own a lot of advantages: more compact structure, higher
output, better quality, more energy saving, easy operation
etc, which can be fit for producing all kinds of high-clarity
packing film, thereby create higher economical efficiency
for you.
4) M3B SERIES THREE-LAYER COEXTRUSION
(REVERSING HAUL-OFF) PACKAGING BLOWN FILM LINE
 Reversing
haul-off with ± 360° horizontal turner bar system, with
stable reversing, consistent linear speed, reasonable
and scientific structure ensure saving energy and easy
operating. By means of the reversing haul-off unit, the
structure of die head is simplified by replacing rotating
die head The reversing haul-off unit resolves many problems
of long channel for dwelling in the rotating die head,
difficult sealing for the melt, easy leakage, unsymmetrical
heating, difficult maintenance, big film thickness tolerance
and so on. The haul-off unit reduces the difficulty for
recipe of the multi-layer co extrusion product and production
technical processing control. If using IBC (Internal Bubble
Cooling system), the blown film line can produce film
with higher transparency and better performance. The produced
film is very flata, and in high-quality by using of reversing
haul-off unit, which can meet demanding for high precision
and high-speed printing.
Mixers and Compounding Equipments
1) Plastic Granular
Material Automatic Compounding Production Line
 BM
series Granular Material Full Automatic Drying Convey
System The system is mainly used in convey, storage, drying
and the production demand. During the whole period, the
PLC central control will be adopted and the central monitor
on the post. The system will meet the needs of the production
art demand and the present condition of the plant house.
The annual output of it is 2000-150000T.
2) PVC Automatic Compounding Production
Line
BM Series Powder Material Automatic Compounding
Production Line.
This system is mainly used for the conveyance of powder
materials. It can be adopted in the negative pressure
and positive pressure (thin phase and thick phase), the
calculation of main materials and auxiliary  materials,
the mixer and the collecting storage. And according to
the site situation, it can be adopted the negative pressure
or screw conveyance to divide materials into each hopper.
During the whole period, the PLC central control will
be adopted and the central monitor on the post as well.
The system will meet the needs of the production art demand
and the present condition of the plant house. The annual
output is2000T-100000T
3) The blade suited for kinds of
raw materials
4) SHL Series 200 -10000 L Cooling Mixers
Uses and Features:SHL  series
and SHR series used together as the proportion of 1:2,
1:3 you can use them with the self combination as you
can. The usage of the combination can be widely used as
process of mixing, drying and colouring of various plastics.
It can make the mixed materials cooled fast in order to
get rid of remaining gases in heating mixed materials
for the materials storage, transfer and follow-up process
well. It has features of advanced design, easy operation,
safe and reliable propertyW, high efficiency low energy
consumption, low noise and corrosion resistance.
5) SRL-VV Series Horizontal Mixer
Unit
Uses and Features
1. It is used in mixing, drying, colouring and other processing.
It is the most ideal equipment for producing shaped plastic
material and plastics pipes.
2. The technology of the main shaft sealed apparatus
has got the state patent with No. ZLP62430641 and it has
two functions of electric and steam heating.
 3.
Two layers of sealing technology are adopted in the pot
cover. The opening of the heating mixed cover adopted
the air opening device and the opening of the cooling
mixed cover adopted hydraulic pressure control system.
4. The electric control section with the programmable
logic control adopted well-known imported meters and control
components.
5. lt is equipped with the pulse dust-cleaning recovery
device.
6. The blades have been passed the relative test.
|
